Top 10 typical forklift crashes ， forklift operation need to focus on these matters ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous accidents including forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take note of these issues ：.

Beginning.
1. Prior to beginning, observe the surroundings, and after confirming that there are no barriers that hinder the security of driving, honk the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge should be safe prior to beginning.
3. When the forklift begins with a lots, the driver ought to first validate that the lots is steady and reliable.
4. The begin needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not raise the fork expensive when driving. When entering and leaving the job site or while driving, take care that there will be no barriers in the sky. When the load is traveling, the fork should not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or automobiles close by, the driving signal must be issued first. High-speed doglegs are banned. High-speed sharp turns will create the car to shed side stability and tip over. .
5. When the forklift is downhill, it is purely forbidden to turn off the fire and slide, and it is forbidden to brake unexpectedly while driving with tons unless there are unique scenarios.
6. When the forklift is running, it should obey the web traffic rules in the factory and must maintain a particular safety range from the vehicle ahead. .
7. When the forklift is running, the load must remain in the lowest position that does not hinder the driving, and the gantry should be properly tilted back. The tons will not be elevated other than when stacking or filling. .
8. The height of the load must not block the vehicle driver's view. In unique conditions, when the item affects the forward vision, drive at a low speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The safe driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will never run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a solitary fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to stand around the fork, so regarding prevent the collapse of the goods and harm people. .
8. Overloading is banned, and it is forbidden to use forks to raise workers to engage in high-altitude procedures to avoid high-altitude dropping mishaps. .
9. It is not permitted to utilize the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to use forks to choose, turn pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork impend. Before leaving the forklift, you have to unload the goods or reduced the fork frame.
2. Pull the hand brake manage to dead or dispirit the hand brake switch.
3. The engine is shut off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the automobile's view and does not exceed 1 minute).
4. Remove the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look needs to be checked, and fuel, lubricating oil and air conditioning water need to be added.
2. Check the security efficiency of beginning, running and Electric Forklift Truck for Warehouse stopping.
3. Examine whether the lights and horn signals are full and effective.
4. During the operation of the forklift, examine whether the stress and temperature level are normal.
5. After the forklift is running, the external leak needs to additionally be inspected and the seals ought to be changed in time.

Forklift Safety Operation Electric Forklift Truck for Warehouse Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to get the goods by turning over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to get the goods.
6. It is not allowed to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work on the pallet or fork, and it is purely prohibited to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roads, train crossings;.
2. Areas with a longitudinal slope more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844